This section provides details on the optical ports and cabling used for the Assured Delivery Blade (ADB) and associated Host Bus Adapter (HBA).
SFP Modules
The ADB and HBA interfaces provide Fibre Channel (FC) connections using an LC physical connector (Fiber-Optic Connections) for optical fibre connections shortwave optics. The ADB and HBA Small Form-factor Pluggable (SFP) modules are field-replaceable.
- ADB interface—The interfaces on the ADB-000000-02 are two 4 Gbps FC SFP optical module ports. The interfaces on the ADB-04210M-01
- HBA interface—The interfaces on the HBA-0204FC are two 4 Gbps FC SFP optical module ports, the interfaces on the HBA-0208FC are two 8 Gbps SFP optical module ports, and the interfaces on the HBA-0216FC are two 16 Gbps SFP optical module ports. The HBA optical ports run standard fibre channel protocols.
ADB Faceplate LEDs
Faceplate LEDs on the ADB indicate the link status for the two ADB SFP module ports, and the read/write status for the flash memory cards. One green and yellow status LED is used for each SFP module port, and one red status LED is used for each internal flash memory card (one for the ADB-000000-02, two for the ADB‑04210M-01
The green port link status LED indicates the state of the SFP physical link:
- Off—Either no link to the SFP module has been established, the module is not receiving power, or the cable connection is not secure.
- On—The link to the SFP module has been established, the module is receiving power, and the cable connection is secure.
If the appliance is reloaded when no SFP module is installed in the mate-link port, the LED behavior for that port will be undefined. However, the port LEDs will properly display the current status once an SFP module is installed and the hardware drivers identify it.
The yellow activity status LED indicates whether there is data activity for the SFP modules:
- Off—The SFP module is not receiving or transmitting messages (including network acknowledgments).
- ON—The SFP module is receiving and transmitting messages (including network acknowledgments).
The red memory card status LED indicates the state of the flash memory card:
- Off—No reading or writing of spooled messages from the flash memory card.
- On—Initialization, read, or write operations are occurring for the flash memory card.
The blade carrier containing the ADB must not be removed from the chassis when the red LED is On.
Faceplate LEDs on ADB-000000-02, ADB 04210M-01-A
Connecting to ADB and HBA SFP Devices
The SFP modules on ADBs and associated HBAs use LC connectors for Fibre Channel connections using shortwave laser optics over MMF cable.
The ADB mate link uses a proprietary cell-based protocol. Refer to in Optical Fibre Specs for Multimode Fibre for the associated optical loss budget and operating distance.
The HBA-0204FC operates according to the 4 Gbps Fibre Channel specification, and the HBA-0208FC operates according to the 8 Gbps Fibre Channel specification. Refer to Optical Fibre Specs for Multimode Fibre for the associated optical loss budget and operating distance.
Typical Network Applications
Redundant Configurations
In the deployment example shown in the figure below, the two appliances form a redundant pair configuration and are connected to each other through Ethernet.
The two ADBs are connected to each other through redundant fibre links, and the two appliances are cross-connected to the redundant disk controllers of an external disk storage array through the HBA. Connection through a fibre channel SAN is also supported.
ADB mate links must be directly connected, and cannot go over ethernet or fiber channel switches.
Solace PubSub+ Event Broker Network - Redundant Configuration
Non-Redundant Configurations
In the deployment example shown in the figure below, the appliance is connected in a point-to-point and non-redundant configuration to the redundant disk controllers of an external disk storage array through the HBA.
All connections are made using standard multi-mode optical fibre cable equipped with LC-type optical connectors.
This configuration may be used by customers who:
- are expecting to migrate to a redundant event broker configuration in the future, but do not currently need use of the event broker redundancy facility for spooling messages to the external disk storage array
- want to take advantage only of the performance benefits associated with spooling messages to the external disk storage array, without use of the event broker redundancy facility
Solace PubSub+ Event Broker Network - Simplex Configuration
